Absen Pakistan logo
SMD Screen Tender Specifications: What Buyers Should Include (Absen Pakistan guide)

SMD Screen Tender Specifications: What Buyers Should Include

Quick answer: A good SMD screen tender names the size, pixel pitch, brightness, refresh rate, certificates, warranty and the tests the screen must pass before handover. Words like “best quality” or “high brightness” let each bidder quote a different product. Measurable terms make the bids easy to compare and make it harder for a weak screen to win on price alone.

If your project is a permanent venue, the Absen fixed installation LED displays range is a common starting point for the specification. The checklist below works for fixed, rental and outdoor tenders. Where the rules change, the section says so.

Why does a tender need a written technical specification?

A tender only works when every bidder answers the same questions. Without a shared list, one supplier quotes a fine pitch with a long warranty, another quotes a coarse panel with a short one, and the buyer cannot tell which bid is right. A written specification protects the buyer and gives suppliers a clear target to quote against.

If the terms are new to your team, read What Is an SMD Screen? first. It explains the parts that the tender will name, such as modules, cabinets and the controller.

Which display specifications should the tender include?

These are the specifications that change the look of the screen and the cost of running it:

  • Pixel pitch: the distance between two pixels, in millimetres. Tie it to the distance at which the audience will stand or sit, not to the lowest price.
  • Size and resolution: the width, height and pixel count of the whole screen. Ask for both, so every bid is measured the same way.
  • Brightness: a target for indoor or outdoor use, measured on the screen itself. A screen for a shaded hall needs much less light than a screen in daylight.
  • Refresh rate and greyscale: important when the screen is filmed or streamed. The LED Screen Refresh Rate guide explains why flicker shows on camera.
  • Viewing angle and colour: the seating plan decides how wide the viewing angle must be.
  • Protection rating: the IP rating for each zone, for dust, water and heat.
SpecificationWhat the tender should sayWhy it matters
Pixel pitchOne value per screen, with the viewing distanceSets sharpness for the audience
BrightnessIndoor or outdoor use, and a measured targetDecides whether content is readable in daylight
Refresh rateA minimum value, confirmed in the datasheetPrevents flicker on camera
ProtectionIP rating for each zoneDust, water and heat exposure
PowerMaximum draw per cabinet and in totalSizes the power supply, UPS or generator

Ask every bidder to attach the datasheet for the exact model they offer. A brochure is not enough.

Which certificates should buyers ask for?

Ask for the certificate of the model being quoted, not a general company brochure. Name the standards you need, such as CE, RoHS or ISO 9001 for the factory, and ask for the certificate number and the body that issued it. Check the number with the issuing body if the tender is for a government or large private client.

Certificates matter most at import. The How to Import LED Screens into Pakistan guide covers duties, grey market risks and the paperwork to ask for. For a quick check that a product is genuine, read How to Spot an Original LED Screen.

What should the warranty clause say?

The warranty should be in writing, with the period stated for each part. Ask the bidder to name:

  • Which parts are covered: modules, power supplies, receiving cards and the controller
  • The warranty period for each part, in years, in the contract
  • Who pays for shipping, labour and on-site visits
  • What happens when a replacement part is out of stock
  • How a claim is reported, and within how many days a response is due

A warranty that covers “the screen” without these details is hard to enforce. The LED Screen Warranty in Pakistan article shows what a real warranty covers and what to check before signing.

How should the brands be compared?

Compare the bids on the same table, not on the brand name. Two screens with the same pixel pitch can differ in module quality, support and spare parts. The Best LED Screen Brands in Pakistan guide gives a checklist for a fair comparison, including factory details, local support and response time.

Which acceptance tests should the tender require?

Acceptance tests decide when the buyer pays the final amount. Write them into the tender so the supplier knows what the screen must pass:

  1. A dead pixel and dead module check across the whole screen
  2. A colour and brightness check with plain white, plain grey and plain red, green and blue images
  3. A long test run at the working brightness, with the temperature checked
  4. Content playback from the controller, including a failover test if a backup is quoted
  5. A check of the drawings, the cable labels and the spare parts list

The LED Screen Installation guide shows the steps from site survey to switch on, so the acceptance tests follow the same order. If the screen shows patches after handover, the SMD Screen Calibration guide explains how a calibration should be done and what to ask for.

What should the commercial terms include?

Price is only one part of a bid. Check these items as well:

  • The installation scope, including the structure, power, cabling and the controller
  • The delivery time and who is responsible for transport and customs
  • A list of spare modules and power supplies, with quantities
  • Training for the operators and a copy of the maintenance routine
  • The as-built drawings and the calibration file, handed over at the end

For a budget range before you write the tender, read SMD Screen Price in Pakistan. Do not use a price range to decide the specification. A specification written around a price will fail the moment a cheaper bid arrives.

Power is often missed in a tender. The SMD Screen Power Consumption guide shows how to plan the supply, the UPS or the generator, so the tender can name the power each bidder must plan for.

How should buyers compare the bids?

Use the same steps for every bid:

  1. Score each bid against the specification table, one line at a time.
  2. Check the certificates for the exact model, not the brand.
  3. Read the warranty clause and mark any part that is not covered.
  4. Ask for a reference site where the same model has run for a long time.
  5. Compare the full cost, including spares, support and power, over the expected life of the screen.

Keep the scoring sheet with the tender file. It shows the decision was made on the specification, not on pressure or a discount.

Related guides: Pixel Pitch Guide: How to Choose and SMD Screen Maintenance Guide.

Frequently asked questions

Should a tender name a single brand?

Name the specification and the certificates, then allow any equal product that meets them. Naming one brand only can limit competition, while accepting any screen can let a weak product in. A clear specification solves both problems.

Which term matters most in an SMD screen tender?

Pixel pitch matters most for the audience, because it sets how sharp the screen looks at the seating distance. Refresh rate matters most when the screen is filmed. Write both down, with the viewing distance and the camera use.

Do I need the warranty in the tender document?

Yes. The warranty period, the covered parts and the claim process should be in the contract, not only in the supplier’s brochure.

Can I ask for a test before I buy?

Yes. Ask the bidder for a demo, a reference site or a sample module where possible. Note what you test, when, and with which content.


About this guide: Written by the Absen Pakistan team at Irfan Corporation, the authorised Absen distributor in Pakistan, with offices in Karachi and Islamabad. Product details come from Absen’s official specifications. Last updated: 6 November 2026.