Quick answer: A cricket stadium uses SMD screens in three places: the main scoreboard, the perimeter boards around the ground and the replay screens for fans. Each needs its own size, pixel pitch and protection, so plan them together.
The Absen A99 perimeter LED boards are designed for the outer edge of a ground, where the boards must be seen from the stands and survive a hard knock. The rest of this guide explains how to plan the three screen types and what to ask a supplier before you buy.
What does a cricket ground need from its screens?
A cricket ground is a large outdoor space, with fans sitting far from the boards and the scoreboard, and cameras that film the boards during every over. The screens have to do three jobs at once:
- Show the score and the match data clearly to fans at the back of the stands.
- Carry advertising on the perimeter, where sponsors pay for visibility on camera.
- Replay the action for fans, so they can see a close catch or a run-out that the stand could not follow.
A screen that does only one of these jobs well is not enough for a stadium. Plan the three together, and decide which one is the priority for the venue.
Scoreboard, perimeter board or replay screen?
The three screen types look similar but are used differently. The table below sums up the main choices for each.
| Screen | Where it sits | Who watches it | What to check |
|---|---|---|---|
| Main scoreboard | High, at one end or on the stand | Fans in every part of the stands | Size, brightness in daylight, and a clear data layout |
| Perimeter board | Low, around the rope or the boundary | Fans in the stands and the camera | Impact protection, water resistance and the pitch that suits the viewing distance |
| Replay screen | Mid height, on a stand or a corner | Fans close to the screen | Pixel pitch for the distance, and smooth motion for replays |
Ask the supplier to show which pitch suits each position. A fine pitch on a high scoreboard wastes money, while a coarse pitch on a replay screen looks poor when fans sit close to it. The Pixel Pitch Guide: How to Choose explains how to match the pitch to the distance.
How bright does a stadium screen need to be?
A stadium screen must be readable in daylight, when the sun is on the stands and the screen is in full view. Brightness matters more for the main scoreboard than for a perimeter board, because the scoreboard is seen from a distance and at many angles.
The Indoor vs Outdoor SMD Screen guide explains why outdoor screens are built for more brightness and better sealing. Set the brightness to suit the time of the match and the light on the screen, rather than running it at the maximum all day. A screen that is too bright in the evening can dazzle the players and the umpires.
What protection does a perimeter board need?
A perimeter board sits close to the pitch, where a ball, a fielder or a spectator can hit it. The product page for the A99 describes an impact-resistant design, with improved impact strength and shock absorption. It also describes waterproof modules and a sealed power box for harsh outdoor conditions.
Impact protection is only part of the plan. Ask the supplier about the following:
- Padding: a soft guard on the lower edge of the board reduces harm to players and fans, and it protects the screen itself.
- Water and dust: monsoon rain, dust and humidity can damage an outdoor screen that is not sealed for them. Check the protection rating and how the power box and vents are sealed.
- Replacement: a damaged module must be replaced quickly, with the same colour and brightness as the rest of the board. Ask how a replacement is matched to the board.
The SMD Screen Maintenance Guide lists the routine checks that keep a board running through a long season.
How do you keep the screens running on match day?
A match runs for hours, and a stadium cannot afford a black screen at a key moment. The A99 product page describes dual power redundancy and triple signal redundancy, meaning two power supplies and three signal paths. Ask the supplier to show how each one works, and how the system switches over if one fails.
Power planning is just as important. A stadium may run on the grid, a generator or both, and the switch between them can cause a short outage. The SMD Screen Power Consumption guide shows how to work out the load for the whole ground, not for one board.
On match day, a small team controls the content. Plan the controller, the sending card and the operator position before the season starts. The SMD Screen Controller Guide explains the parts of the signal chain and how a live feed reaches the screen.
Should the venue rent or buy the screens?
Many cricket venues use screens only for big events, such as a league final or a national series, and sit idle for the rest of the year. In that case, renting can make more sense than buying. The SMD Screen on Rent or Buy guide shows how to compare the two costs.
A permanent installation makes more sense for a venue that shows the score and sponsor content every match. Perimeter boards can also earn money through ad slots, and the SMD LED Billboard Business in Pakistan guide explains how screen owners plan that income.
How should the installation be planned?
Plan the installation around the match schedule, because the ground may be closed for weeks during the work. Check the following before the contract is signed:
- The structure of the stand and the perimeter, checked by an engineer for the weight and the wind load.
- The route for the power and signal cables, kept away from the fans and the players.
- The access for service, from the front or the rear. The Front Service vs Rear Service guide explains which access suits which screen.
- The acceptance tests, as set out in the LED Screen Installation guide.
A stadium screen is a long-term asset. Ask for the warranty for each part in writing, as the LED Screen Warranty in Pakistan article explains, and ask for the spares list before the first match.
Related guides: Outdoor LED Billboard in Pakistan and Indoor vs Outdoor SMD Screen.
Frequently asked questions
It depends on the size of the ground and the distance from the farthest seat to the scoreboard. Measure that distance first, then ask the supplier to size the scoreboard and the replay screens to suit it.
Yes. Perimeter boards are often sold as ad slots, and they can be seen by fans and by the camera. The content must be planned so that the advertising and the match information do not clash.
Outdoor screens are built to be sealed against rain, but the seal depends on the design and the installation. Ask for the protection rating in writing, and check how the power box and vents are sealed.
A trained operator controls the content from a fixed position in the stadium. Plan this position, the cabling and the backup controller before the season starts.
About this guide: Written by the Absen Pakistan team at Irfan Corporation, the authorised Absen distributor in Pakistan, with offices in Karachi and Islamabad. Product details come from Absen’s official specifications. Last updated: 9 November 2026.